84 | | == 先人の事例 == |
85 | | 1. レーザーカッター[[BR]] |
86 | | たとえば、[http://www.ladyada.net/library/smt/laserstencils.html Adafruitさん]がやっています。 |
87 | | ここでは、カプトンフィルム(ポリイミドフィルム)を使っています。 |
88 | | カプトンは熱を加えても融けないため、開口部の周囲が盛り上がってしまう事がありません。 |
89 | | これは利点ですが、カプトンは高価なのが難点です。また、融けない=燃やして穴を開けるため、ピッチが細かい物はうまくいかないようです。 |
90 | | カプトンを加熱すると有毒ガスが出てくるのもイヤです。 |
91 | | カプトンの代わりにPETフィルムを使うと、開口部の周囲が盛り上がる、開いた穴が融けて再融着してしまうという問題があります。 |
92 | | 1. カッティングプロッタ[[BR]] |
93 | | たとえば、[http://www.instructables.com/id/Create-Solder-Paste-Stencils-with-Cricut/ Instructables]でも、先人ががんばっています。 |
94 | | この手法では、データの処理に割りと手作業が多いのが難点です。 |
95 | | また、カッティングプロッタの機種のせいか、精度が低くて四角が楕円になってるのが問題です。 |
| 81 | * Polyimide film |
| 82 | Polyimide film emits poisonous gas under high-temperature. The cutting edge is not straight. |
101 | | - 燐青銅板[[BR]] |
102 | | エッチングまたはCNCミルで穴を開ける。 |
103 | | エッチングは、[http://blog.indoor-airplane.shop-pro.jp/?cid=11022 インドアプレーンのtokoさん]がやってらっしゃいます。 |
104 | | データの前処理が大変、表裏のマスクの位置合わせが大変、ピッチが細かいと無理、廃液処理が大変。 |
105 | | CNCは、エンドミルの径をあまり細くできないので、開口部が丸くなります。また、高価なエンドミルがどんどんダメになる。 |
106 | | - PETフィルム(マイラー)[[BR]] |
107 | | 硬くて切り抜けない。100μmくらいが限度。硬いので、細かい部分が折れやすい。隣のパッドとつながる。 |
108 | | - 塩化ビニール[[BR]] |
109 | | 伸びる。アルコール等の薬品に弱い。 |
110 | | - ラミネートパウチ用フィルム(PET+塩化ビニル)[[BR]] |
111 | | 塩ビの層がネチャついて、切り抜けない事がある。同じ厚さのPETよりも切りやすいぶん、弱く、すぐにダメになる。 |
112 | | アルコール等の薬品に弱い。PETと塩ビの層がはがれる。 |
113 | | - カプトンフィルム(ポリイミドフィルム)[[BR]] |
114 | | 融けないので、レーザーで切った際に再融着しない、切り口が盛り上がらない。高価、加熱すると有毒ガスが出る。 |
115 | | - ポリプロピレン合成紙[[BR]] |
116 | | 水やアルコールに強い。あまり伸びない。手で切れないくらい丈夫だけど、カッターには弱いから切りやすい。 |
117 | | 切り口はぼそぼそしていて、あまり綺麗ではない。願わくば、表面がツルツルだといい。 |
| 89 | * Phosphor bronze plate |
| 90 | The cutting edge wells up. |
| 92 | The hole size and the diameter of the corner depend on the endmill diameter. The larger endmill is proper for high-speed manufacturing and slow degradation of endmills, but it is not proper for fine pitch PCB design. The small size endmill easily degrades and it is expensive. |
| 93 | |
| 94 | === Cutting plotter === |
| 95 | We tried cutting 4 kinds of materials, PET-film, vinyl chloride sheet, laminate film, and polypropylene synthetic paper using a cutting plotter named Craft-ROBO (made by Japanese company GRAPHTEC). |
| 96 | |
| 97 | * PET-film |
| 98 | The rigidity of the PET-film makes it easy to be broken, and the neighboring pads easily get together. It cannot be used for fine pitch PCB design. And our Craft-ROBO could not cut out if thicker than 100um (micro-meter). |
| 99 | |
| 100 | * Vinyl chloride |
| 101 | It stretches easily, i.e., the accuracy is low. It is weak against alcohol. |
| 102 | |
| 103 | * Laminate film |
| 104 | Laminate film is the double-layered film of PET-film and vinyl chloride, generally used for laminate pouches. It is difficult to cut completely because the vinyl chloride layer is soft, but the accuracy is not so low. However, it tends to tear easily. |
| 105 | |
| 106 | * Polypropylene synthetic paper |
| 107 | Polypropylene synthetic paper is paper like sheet made of polypropylene fiber. It is easy to cut completely, of course it is a paper, i.e., the accuracy is high enough. It is just paper, but it is difficult to tear by hands, i.e., it is tough enough for stencil use. It has good resistance to alcohol and water. |
| 108 | |
| 109 | Based on the results, we chose the cutting plotter and polypropylene synthetic paper. |